Bored Pile Construction Equipment Hydraulic Rotators With Wired Remote Control Mode

  • 0

Bored Pile Construction Equipment Hydraulic Rotators With Wired Remote Control Mode

Category : Uncategorized

Bored Pile Construction Equipment Hydraulic Rotators With Wired Remote Control Mode

 

Casing Rotator KTR1505L and Hydraulic Power Pack

 

About Hydraulic Power Pack

 

We have the emergency system, the main function of control system is also set in the power pack, when there is one malfunction, the emergency system can be adopted to complete the construction work.

 

We have the cutter head load auomatic control system, when cutting the hard rock, it can well protect the cutter head and effctively enhance the cutting efficiency by the automatic control computer.

 

Also we have the convenient operating system, according to the working condition the operating system platform of micro computer can keep the machine at an optimum working state by adjusting the speed, torque and pressing force, and promote the work efficiency to the maximum.

 

1. Specifications

 

Technical parameters
Drilling Diameter 800-1500 mm
Torque 1550/975/600 kN.m
Rotary speed 1.6/2.46/4.0
Lower Pressure of sleeve Max. 360kN+Dead Weight 210 kN
Pulling fore of sleeve 2444kN, Instantaneous 2690 kN
Pressure pulling stroke 750 mm
Weight 32 ton

 

 

Parameters of Hydraulic power station
Engine Model ISUZU AA-6HK1XQP
Engine Power 183.9/2000 kw/rpm
Fuel Consumption of Engine 226.6 g/kwh( Max. power rate)
Weight 7 ton
Control Mode Wired remote control

 

2. Description

Use for different types construction:

 

(1) Foundation pile, continuous wall

Foundation piles for high-speed rail, road and bridge and house building;

Articulation pile constructions which are required to be excavated, such as subway platforms, underground architectures, continuous walls.

Water retaining wall of reservoir reinforcement.

 

(2)Drilling gravels, boulders and karst caves

It is allowable to conduct the foundation pile construction at mountain lands with gravel and boulder formations.

It is allowable to conduct operation and cast the foundation piles at the thick quicksand formation and necking down stratum or the filling layer.

Conduct rock-socketed drilling to the rock stratum, cast the foundation pile.

 

(3) Clear the underground obstructions

During the urban construction and bridge rebuilding, the obstructions such as the steel reinforced concrete pile, steel pipe pile, H steel pile, pc pile and wood pile can be cleared directly, and cast the foundation pile on the spot.

 

(4) Cut the rock stratum

Conduct the rock-socketed drilling to the cast-in-place piles.

Drill through-holes on the rock bed(shafts and ventilation holes).

 

(5) Deep excavation

Conduct the in-place casting or steel pipe pile inserting for the deep foundation improvement.

Excavate deep wells for construction use in the constructions of reservoir and tunnel.

 

3.Competitive Advantage

 

(1) No noise, no vibration, and high safety.

 

(2) Without mud, clean working surface, good environmental friendliness, avoiding the possibility for mud to enter the concrete, high pile quality, enhancing the bond stress of concrete to the steel bar;

 

(3) During construction drilling, the characteristics of stratum and rock can be directly distinguished;

 

(4) The drilling speed is fast and reaches about 14m/h for the general soil layer;

 

(5) The drilling depth is large and reaches about 80m according to the situation of soil layer;

 

(6) The hole forming verticality is easy to master, which can be accurate to 1/500;

 

(7) No hole collapse will be caused, and the hole forming quality is high;

 

(8) The hole forming diameter is standard, with little filling factor. Being compared with other hole forming methods, it can save a lot of concrete usage;

 

(9) The hole clearing is thorough and fast. The drilling mud at the hole bottom can be clear to about 3.0cm.


Leave a Reply