Daily Archives: October 8, 2016

  • 0

210Kw Mining Industry Equipment Overflow Ball Mill 22Tonne With Gas Clutch

Category : Uncategorized

210Kw Mining Industry Equipment Overflow Ball Mill 22Tonne With Gas Clutch



Type Overflow Type Ball Mill
Model MTP2136
Cylinder Diameter (mm) 2100
Cylinder Length (mm) 3600
Motor Model JR137-8
Motor Power (kW) 210
Length (mm) 9300
Width (mm) 4840
Height (mm) 3795
Effective Volume (m3) 10.8
Max. Ball Load (t) 22
Weight (kg) 52010

Product Introduction:

A ball mill with simple structure.

Product Improvement:

Wet type overflow ball mill is lined with SINOMTP wear-resistant rubber sheet with excellent wear resistance, long service life and convenient maintenance.


  • Jack-up device, easy maintenance
  • The hydrostatic and hydrodynamic bearings ensure the smooth operation
  • Low speed transmission is easy for starting and maintenance
  • The oil-mist lubrication device guarantees reliable performance of bearings
  • The gas clutch adopts the flexible start-up model


Products feature:


The discharging of wet type overflow ball mill relies on the inclination because of the outlet hollow shaft diameter larger than inlet hollow shaft diameter. When the slurry surface is higher than outlet generatrix, the slurry overflow discharges from the mill


  • 0

30- 450 TPH Stone Crushing Plant in Quarry Railway Highway Stone Crusher Machine

Category : Uncategorized

30- 450 TPH Stone Crushing Plant in Quarry Railway Highway Stone Crusher Machine




Quarry stone crushing plant is suitable for crushing soft rock or stone with compressive strength less than 150 MPa, such as limestone, dolomite, shale, gypsum, and hard rock, such as granite and basalt. The max feeding size is 1000mm.




It is widely used in highway, railway, hydroelectric dam construction, quarry, cement, building materials, and chemical industry.


Equipment Configuration of Stone Crushing Plant:


1. Vibrating feeder + jaw crusher + impact crusher + belt conveyor + circular vibrating screen. ( for soft stone, such as limestone, dolomite, gypsum, shale)

2. Vibrating feeder + jaw crusher + cone crusher + belt conveyor + vibrating screen. ( for hard rock, such as granite and basalt)

3. Vibrating feeder + jaw crusher + impact crusher (cone crusher) + VSI impact sand making machine + vibrating screen.


Technical Data:




Major equipment type, size, number
Feeding equipment Crushing




Classification and screening


Belt Conveyor(m) Installed power(kw)
30 GZD8030 PE400×600 PF1008 2YK1235 60-90 120
50 GZD8530 PE400×600 PF1008 3YK1235 100-130 140
80 GZD9636 PE500×750 PF1010 3YK1545 130-160 200
100 GZD9638 PE600×900 PF1210 3YK1545 140-180 280
150 GZD1142 PE750×1060 PF1214 3YK1854 200-240 300
200 GZD1142 PE750×1060 PF1315 3YK1860 200 350
250 GZD1149 PE750×1060 PF1214/2 3YK2160 200 400
300 GZD1249 PE900×1200 PF1315/2 3YK2160 250 450
350 GZD1349 PE1000×1200 PF1315/2 3YK2460 250 500
450 GZD1349 PE1000×1200 PF1315/2 PF1214 3YK2160/2 350 600

  • 0

Bored Pile Construction Equipment Hydraulic Rotators With Wired Remote Control Mode

Category : Uncategorized

Bored Pile Construction Equipment Hydraulic Rotators With Wired Remote Control Mode


Casing Rotator KTR1505L and Hydraulic Power Pack


About Hydraulic Power Pack


We have the emergency system, the main function of control system is also set in the power pack, when there is one malfunction, the emergency system can be adopted to complete the construction work.


We have the cutter head load auomatic control system, when cutting the hard rock, it can well protect the cutter head and effctively enhance the cutting efficiency by the automatic control computer.


Also we have the convenient operating system, according to the working condition the operating system platform of micro computer can keep the machine at an optimum working state by adjusting the speed, torque and pressing force, and promote the work efficiency to the maximum.


1. Specifications


Technical parameters
Drilling Diameter 800-1500 mm
Torque 1550/975/600 kN.m
Rotary speed 1.6/2.46/4.0
Lower Pressure of sleeve Max. 360kN+Dead Weight 210 kN
Pulling fore of sleeve 2444kN, Instantaneous 2690 kN
Pressure pulling stroke 750 mm
Weight 32 ton



Parameters of Hydraulic power station
Engine Model ISUZU AA-6HK1XQP
Engine Power 183.9/2000 kw/rpm
Fuel Consumption of Engine 226.6 g/kwh( Max. power rate)
Weight 7 ton
Control Mode Wired remote control


2. Description

Use for different types construction:


(1) Foundation pile, continuous wall

Foundation piles for high-speed rail, road and bridge and house building;

Articulation pile constructions which are required to be excavated, such as subway platforms, underground architectures, continuous walls.

Water retaining wall of reservoir reinforcement.


(2)Drilling gravels, boulders and karst caves

It is allowable to conduct the foundation pile construction at mountain lands with gravel and boulder formations.

It is allowable to conduct operation and cast the foundation piles at the thick quicksand formation and necking down stratum or the filling layer.

Conduct rock-socketed drilling to the rock stratum, cast the foundation pile.


(3) Clear the underground obstructions

During the urban construction and bridge rebuilding, the obstructions such as the steel reinforced concrete pile, steel pipe pile, H steel pile, pc pile and wood pile can be cleared directly, and cast the foundation pile on the spot.


(4) Cut the rock stratum

Conduct the rock-socketed drilling to the cast-in-place piles.

Drill through-holes on the rock bed(shafts and ventilation holes).


(5) Deep excavation

Conduct the in-place casting or steel pipe pile inserting for the deep foundation improvement.

Excavate deep wells for construction use in the constructions of reservoir and tunnel.


3.Competitive Advantage


(1) No noise, no vibration, and high safety.


(2) Without mud, clean working surface, good environmental friendliness, avoiding the possibility for mud to enter the concrete, high pile quality, enhancing the bond stress of concrete to the steel bar;


(3) During construction drilling, the characteristics of stratum and rock can be directly distinguished;


(4) The drilling speed is fast and reaches about 14m/h for the general soil layer;


(5) The drilling depth is large and reaches about 80m according to the situation of soil layer;


(6) The hole forming verticality is easy to master, which can be accurate to 1/500;


(7) No hole collapse will be caused, and the hole forming quality is high;


(8) The hole forming diameter is standard, with little filling factor. Being compared with other hole forming methods, it can save a lot of concrete usage;


(9) The hole clearing is thorough and fast. The drilling mud at the hole bottom can be clear to about 3.0cm.

  • 0

Diaphragm Walls Construction Heavy Duty Equipment , Rental Construction Equipment

Category : Uncategorized

Diaphragm Walls Construction Heavy Duty Equipment , Rental Construction Equipment

1. Easy for operation and maintenance.

2. Multifunction & high efficience.

3. High reliable & stable quality.

4. Low noise & low emission.

5. Good performance.

Technical specification of KH400 diaphragm wall grab
Length of grooving (a) 3500 mm
Width of grooving (b) 400~1000 mm
Depth of grooving 60 m
Capacity of grab bucket 0.8~1.8 m³
Diameter of steel wire rope 28 m
Weight 9.8~11.9 t
Grab weight 9~11.5 t
Excavation volum 0.85~1.3 m³
Excavators weight 2~3 t
Crawler cranes ≤40 t
Requirements pull 200 KN

A Brief introduction of this KH400 diaphragm wall grab:

1. A conventional underground continuous operation trenching equipment .

2. Operated by using the crawler crane, achieved the international concept of “multi-function machine”.

3. Simple structure, easy to operate, and easy to maintain.

Equipped with our grab bucket, single bucket capacity up to 1.3 cubic meters.

4. The groove width is 400-600 mm, the maximum groove depth ca



Q1: What’s the type of this diaphragm wall grab?

This is mechanical diaphragm wall grab.

Q2: Which machine does this diaphragm wall grab combine to use?

Crawler crane.